here's another diamond in the rough.
http://mikesreelrepair.com/schematics/schematic.php?url=Daiwa/Daiwa SL450H, 450HW.pdf
and here's your reel.
let's start with the left side plate. back out the three left side plate screw A's (key #2) and the two left side side plate screw B's (key #3) one at a time, grease the screw holes and re-install the screws.
now back out the three right side plate screw A's (key #48) and two right side plate screw B's (key #49).
set them aside.
you now have a frame assembly (key #16), a spool (key #24) and right side plate assembly (key #36).
aluminum frames tend to corrode. take an old toothbrush and spread the old grease around a little, then wipe off all the excess.
lube the left side plate bearing (key #13).
ok, the wing nuts have to go.
you have a choice of replacing just the clamp nuts and bolts, or the entire clamp all together. the bolts are penn part #34-35, the hex nuts are #149-200, the clamp nuts are 149-45, the bolt/hex nut/clamp nut kit is #34C-45, the penn clamp is #33-340, and the entire kit is called a 33-340sp kit. these are all penn parts.
for this reel, we're going to replace everything but the clamp. nice, huh!
install the spool (key #24) into the frame assembly (key #16) and set both aside.
now, for the right side plate. remove the handle lock screw (key #61).
remove the handle screw (key #60). a penn wrench works well here.
remove the handle (key #59) and handle washer (key #58).
remove the star drag (key #57).
remove the tension springs (key #56). note that they are cupped "()".
remove the three set plate screw A's (key #42) and the single set plate screw B (key #63).
the set plate assembly (key #25) will drop out as a unit.
here is an exploded view of the gear cluster. the stock daiwa drag washers will be replaced with a single penn ht-100 #6-855 and a set of five penn ht-100 #6-113h's. the #6-113h drag washers are thinner that the stock daiwa drag washers and will be doubled up to maintain the proper height.
we will be very happy to be replacing these particle board drag washers with penn drag washers.
http://mikesreelrepair.com/schematics/schematic.php?url=Daiwa/Daiwa SL450H, 450HW.pdf
and here's your reel.
let's start with the left side plate. back out the three left side plate screw A's (key #2) and the two left side side plate screw B's (key #3) one at a time, grease the screw holes and re-install the screws.
now back out the three right side plate screw A's (key #48) and two right side plate screw B's (key #49).
set them aside.
you now have a frame assembly (key #16), a spool (key #24) and right side plate assembly (key #36).
aluminum frames tend to corrode. take an old toothbrush and spread the old grease around a little, then wipe off all the excess.
lube the left side plate bearing (key #13).
ok, the wing nuts have to go.
you have a choice of replacing just the clamp nuts and bolts, or the entire clamp all together. the bolts are penn part #34-35, the hex nuts are #149-200, the clamp nuts are 149-45, the bolt/hex nut/clamp nut kit is #34C-45, the penn clamp is #33-340, and the entire kit is called a 33-340sp kit. these are all penn parts.
for this reel, we're going to replace everything but the clamp. nice, huh!
install the spool (key #24) into the frame assembly (key #16) and set both aside.
now, for the right side plate. remove the handle lock screw (key #61).
remove the handle screw (key #60). a penn wrench works well here.
remove the handle (key #59) and handle washer (key #58).
remove the star drag (key #57).
remove the tension springs (key #56). note that they are cupped "()".
remove the three set plate screw A's (key #42) and the single set plate screw B (key #63).
the set plate assembly (key #25) will drop out as a unit.
here is an exploded view of the gear cluster. the stock daiwa drag washers will be replaced with a single penn ht-100 #6-855 and a set of five penn ht-100 #6-113h's. the #6-113h drag washers are thinner that the stock daiwa drag washers and will be doubled up to maintain the proper height.
we will be very happy to be replacing these particle board drag washers with penn drag washers.